Template:LabelingSamples

Sample Scenario 1 :: All Good[edit]

Labeling Tutorial 1. How to check marker labels in Motive

When recorded 3D data have been labeled properly and entirely throughout the Take, you will not need to edit marker labels. If you don't have 3D data recorded, you can reconstruct and auto-label the Take to obtain 3D data and label all of the skeleton and rigid body markers. If all of the markers are well reconstructed and there are no significant occlusions, auto-labeled 3D data may be acceptable right away. In this case, you can proceed without post-processing of marker labels.

  1. Recorded 3D data has no gaps in the labels, or the Reconstruct and Auto-label works perfectly the first time without additional post-processing.
  2. Examine the Take(s). Check the Labeling pane, or the tracks view, to make sure no occlusion exists within the capture, and all markers are consistently labeled.
  3. Done.

Sample Scenario 2 :: Labeling errors in the middle of a Take[edit]

When skeleton markers are mislabeled only within specific frame ranges of a Take, you will have to manually re-label the markers. This may occur when a subject performs dynamic movements or come into contact with another object during the recorded Take. After correcting the mislabeled markers, you can also use the auto-labeler to assign remaining missing labels.

  1. Start with recorded 3D data or Reconstruct and auto-label the Take to obtain newly labeled 3D data.
  2. Inspect the Take to pick out the frame ranges with bad tracking.
  3. If markers are mislabeled during majority of the capture, unlabel all markers from the entire capture by right-clicking on the Take in Data Management pane and click Delete Marker Labels. You can do this on selected frame ranges as well.
  4. Scrub the timeline to a frame just before the bad tracking frame range.
  5. Using the Labeling pane, manually label the skeleton. Depending on the severity of the mislabels, you can either label the entire skeleton or just the key segments starting from the hip.
  6. Scrub the timeline to a frame after the bad tracking frame range.
  7. Manually label the same skeleton.
  8. Auto-label the Take.
  9. Check the frames again and correct any remaining mislabels using the Labeling pane.

Sample Scenario 3 :: Skeletons never acquire perfectly throughout a Take[edit]

Labeling Tutorial 3. Auto-label.

For Take(s) where skeletons are never perfectly tracked and the markers are consistently mislabeled, you will need to manually assign the correct labels for the skeleton asset(s). Situations like this could happen when the skeleton(s) are never in an easily trackable pose throughout the Take (e.g. captures where the actors are rolling on the ground). It is usually recommended that all skeleton ‘’Takes’’’ start and end with T-pose in order to easily distinguish the skeleton markers. This also helps the skeleton solver to correctly auto-label the associated markers; however, in some cases, only specific section of a Take needs be trimmed out, or including the calibration poses might not be possible. Manually assigning labels can help the auto-labeler to correctly label markers and have skeletons acquire properly in a Take. You will get best results if you manually label the entire skeleton, but doing so can be time-consuming. You can also label only the mislabeled segment or the key segment (hip bone) and run the auto-labeler to see if it correctly assigns the labels with the small help.

  1. Start with recorded 3D data or Reconstruct the Take.
  2. At a certain point of the Take (usually at a frame where you can best identify the pose of the skeleton), use the Labeling pane to manually assign the marker labels for skeletons that are not labeling correctly. Depending on the severity of the mislabels, you can either label the entire skeleton or only the key segments starting from the hip.
  3. After manually assigning the labels, auto-label the Take. Make sure the corresponding assets are enabled in the Assets pane.
  4. Check to see if all markers are correctly assigned throughout the take. If not, re-label or unlabel, any mislabeled markers and run auto-label again if needed.

Sample Scenario 4 :: Mislabeling/unlabeling of a marker due to occlusions[edit]

Marker occlusions can be critical to the auto-labeling process. After having a gap for multiple frames, occluded markers can be unlabeled entirely, or nearby reconstructions can be mistakenly recognized as the occluded marker and result in labeling swaps or mislabels. Skeleton and rigid body asset definitions may accommodate labeling for such occlusions, but in some cases, labeling errors may persist throughout the Take. The following steps can be used to re-assign the labels in this case.

If tracked markers are relatively stationary during the occluded frames, you may want to increase the Maximum Marker Label Gap value under the Auto-Labeler settings in the Reconstruction pane to allow the occluded marker to maintain its label after auto-labeling the Take. However, note that adjusting this setting will not be useful if the marker is moving dynamically beyond the Prediction Radius (mm) settings during occlusion.

  1. Start with recorded 3D data or Reconstruct and auto-label the Take
  2. Examine through the Take, and go to a frame where markers are mislabeled right after an occlusion.
  3. In the Labeling pane, disable the Increment Label Selection Label Increment 20.png option, and select a marker set and a label that is frequently occluded.
  4. In the Labeling pane, disable the Apply Labels to Previous Frames Label ApplyBefore.png option, and leave only the Apply Labels to Upcoming Frames Label ApplyAfter.png option enabled.
  5. Using the Quick Label Mode, correct the labeling errors.
  6. Move onto next occluded frames. When the marker reappears, correct the labels.
  7. After correcting the labels, Auto-label the Take again.
  8. Use the Fill Gaps tool in the Editing tools to interpolate the occluded trajectories.