Main Page → Motive Documentation → Labeling
This page provides basic description of marker labels and instructions on labeling workflow in Motive.
There are two main approaches for labeling markers in Motive:
When tracking rigid bodies and skeletons, Motive can automatically label associated markers both in real-time and post-processing. The auto-labeler uses active asset definitions to search for related markers and labels them with pre-defined names throughout each frame of 3D data. Using the auto-labeler, it wouldn't be necessary to individually assign marker labels for trackable assets.
There are times, however, when it is necessary to manually label a section or all of a trajectory, either because the markers of a rigid body or a skeleton were misidentified (or unidentified) during capture or because individual markers need to be manually labeled. In these cases, the Labeling Pane in Motive is used to perform manual labeling of individual trajectories. Manual labeling workflow is supported only for post-processing of a capture when a Take file (TAK) has been loaded with 3D data as its playback type. In case of 2D data only capture, the Take must be Reconstructed first in order to assign, or edit, the marker labels in its 3D data. This manual labeling process is typically referred to as post processing of recorded mocap data along with the process of editing reconstructed marker data. For more details on editing 3D data, see more in the Data Editing page.
Rigid body and skeleton asset definitions contain information of marker placements on corresponding assets. This is recorded when the assets are first created, and the auto-labeling pipeline in Motive uses them to label a set of reconstructed 3D trajectories that resemble marker arrangements of active assets. Once all of the markers on active assets are successfully labeled, corresponding rigid bodies and skeletons get modeled in the 3D viewport.
Note: Be careful when reconstructing a Take again either by Reconstruct or Reconstruct and Auto-label, because it will overwrite the 3D data and any post-processing edits on trajectories and marker labels will be discarded. Also, for Takes involving skeleton assets, the recorded skeleton marker labels, which were intact during the live capture, may be discarded, and reconstructed markers may not be auto-labeled again if the skeletons are never in well-trackable poses throughout the captured Take. This is another reason why you want to start a capture with a calibration pose (e.g. T-pose).
The MarkerSet is a type of assets in Motive. It is the most fundamental method of grouping related markers, and this can be used to manually label individual markers in post-processing of captured data using the Labeling pane. Note that MarkerSets are used for manual labeling only. For automatic labeling during live mode, a Rigid Body asset or a Skeleton asset is necessary.
Since creating rigid bodies, or skeletons, groups the markers in each set and automatically labels them, MarkerSets are not commonly used in the processing workflow. However, they are still useful for marker-specific tracking applications or when the marker labeling is done in pipelines other than auto-labeling. Also, marker sets are useful when organizing and reassigning the labels.
The Labeling pane is used to assign, remove, and edit marker labels in the 3D data. The Tracks View under the Graph View pane can be used in conjunction with the Labeling pane to monitor which markers and gaps are associated. The Labeling pane is also used to examine the number of occluded gaps in each label, and it can be used along with the Editing Tools for complete post-processing.
Using the Labeling pane, you can assign marker labels for each asset (MarkerSet, Rigid Body, and Skeleton) via the QuickLabel Mode . The Labeling Pane also shows a list of labels involved in the Take and their corresponding percent completeness values. The percent completeness values indicate frame percentages of a Take for which the trajectory has been labeled. If the trajectory has no gaps (100% complete), no number will be shown. You can use this pane together with the Graph View pane to quickly locate gaps in a trajectory.
For a given frame, all labels are color-coded. For each frame of 3D data, assigned marker labels are shown in white, labels without reconstructions are shown in red, and unlabeled reconstructions are shown in orange; similar to how they are presented in the 3D View.
See the Labeling Pane page for detailed explanation on each option.
The QuickLabel mode allows you to tag labels with single-clicks in the view pane, and it is a handy way to reassign or modify marker labels throughout the capture. When the QuickLabel mode is toggled, the mouse cursor switches to a finger icon with the selected label name attached next to it. Also, when the display label option is enabled in the perspective view, all of assigned marker labels will be displayed next to each marker in the 3D viewport, as shown in the image below. Select the marker set you wish to label, and tag the appropriate labels to each marker throughout the capture.
When assigning labels using the Quick Label Mode, the labeling scope is configured from the labeling range settings. You can restrict the labeling operation to apply from the current frame backward, current frame forward, or both depending on the trajectory. You may also restrict labeling operations to apply the selected label to all frames in the Take, to a selected frame range, or to a trajectory 'fragment' enclosed by gaps or spikes. The fragment/spike setting is used by default and this best identifies mislabeled frame ranges and assigns marker labels. See the Labeling pane page for details on each feature.
The following section provides the general labeling steps in Motive. Note that the labeling workflow is flexible and alternative approaches to the steps listed in this section could also be used. Utilize the auto-labeling pipelines in combination with the Labeling pane to best reconstruct and label the 3D data of your capture.
Step 1. In the Data Management pane, Reconstruct and auto-label the take with all of the desired assets enabled.
Step 2. In the Graph View pane, examine the trajectories and navigate to the frame where labeling errors are frequent.
Step 3. Open the Labeling pane.
Step 4. Select an asset that you wish to label.
Step 5. From the label columns, Click on a marker label that you wish to re-assign.
Step 6. Inspect behavior of a selected trajectory and its labeling errors and set the appropriate labeling settings (allowable gap size, maximum spike and applied frame ranges).
Step 7. Switch to the QuickLabel mode (Hotkey: D).
Step 8. On the Perspective View, assign the labels onto the corresponding marker reconstructions by clicking on them.
Step 9. When all markers have been labeled, switch back to the Select Mode.
Step 1. Start with 2D data of a captured Take with model assets (skeletons and rigid bodies).
Step 2. Reconstruct and Auto-Label, or just Reconstruct, the Take with all of the desired assets enabled under the Assets pane. If you use reconstruct only, you can skip step 3 and 5 for the first iteration.
Step 3. Examine the reconstructed 3D data, and inspect the frame range where markers are mislabeled.
Step 4. Using the Labeling pane, manually fix/assign marker labels, paying attention to your label settings (direction, max gap, max spike, selected duration).
Step 5. Unlabel all trajectories you want to re-auto-label.
Step 6. Auto-Label the Take again. Only the unlabeled markers will get re-labeled, and all existing labels will be kept the same.
Step 7. Re-examine the marker labels. If some of the labels are still not assigned correctly from any of the frames, repeat the steps 3-6 until complete.
The general process for resolving labeling error is:
For more data editing options, read through the Data Editing page.
Following tutorials use Motive 1.10. On Motive 2.0., Data Management pane and Assets pane is used instead of the Project pane.
When recorded 3D data have been labeled properly and entirely throughout the Take, you will not need to edit marker labels. If you don't have 3D data recorded, you can reconstruct and auto-label the Take to obtain 3D data and label all of the skeleton and rigid body markers. If all of the markers are well reconstructed and there are no significant occlusions, auto-labeled 3D data may be acceptable right away. In this case, you can proceed without post-processing of marker labels.
When skeleton markers are mislabeled only within specific frame ranges of a Take, you will have to manually re-label the markers. This may occur when a subject performs dynamic movements or come into contact with another object during the recorded Take. After correcting the mislabeled markers, you can also use the auto-labeler to assign remaining missing labels.
For Take(s) where skeletons are never perfectly tracked and the markers are consistently mislabeled, you will need to manually assign the correct labels for the skeleton asset(s). Situations like this could happen when the skeleton(s) are never in an easily trackable pose throughout the Take (e.g. captures where the actors are rolling on the ground). It is usually recommended that all skeleton ‘’Takes’’’ start and end with T-pose in order to easily distinguish the skeleton markers. This also helps the skeleton solver to correctly auto-label the associated markers; however, in some cases, only specific section of a Take needs be trimmed out, or including the calibration poses might not be possible. Manually assigning labels can help the auto-labeler to correctly label markers and have skeletons acquire properly in a Take. You will get best results if you manually label the entire skeleton, but doing so can be time-consuming. You can also label only the mislabeled segment or the key segment (hip bone) and run the auto-labeler to see if it correctly assigns the labels with the small help.
Marker occlusions can be critical to the auto-labeling process. After having a gap for multiple frames, occluded markers can be unlabeled entirely, or nearby reconstructions can be mistakenly recognized as the occluded marker and result in labeling swaps or mislabels. Skeleton and rigid body asset definitions may accommodate labeling for such occlusions, but in some cases, labeling errors may persist throughout the Take. The following steps can be used to re-assign the labels in this case.
If tracked markers are relatively stationary during the occluded frames, you may want to increase the Maximum Marker Label Gap value under the Auto-Labeler settings in the Reconstruction pane to allow the occluded marker to maintain its label after auto-labeling the Take. However, note that adjusting this setting will not be useful if the marker is moving dynamically beyond the Prediction Radius (mm) settings during occlusion.
Back: Data Types
Next: Data Editing