Quick Start Guides
Active Marker Tracking
Prepare Setup Area
Camera Mount Structures
Cabling and Wiring
Aiming and Focusing
Rigid Body Tracking
Camera Video Types
Reconstruction and 2D Mode
Motive Batch Processor
Motive UI Pages
Application Settings pane
Data Management pane
Data Streaming pane
Edit Tools pane
Graph View pane
Rigid Body pane
External Device Setup
AMTI Force Plate
Bertec Force Plate
This wiki is intended for older versions of Motive. For the latest documentation, please refer to
Baseline + Hinged Toe, with Headband (41)
Back to the Baseline Markerset page
Baseline + Hinged Toe, with Headband (41) Marker Placements
When a headband — instead of the mocap beanie — is used to place the head markers, the HeadTop marker is removed and an extra HeadSide marker is added.
Place the marker at the center of the forehead.
Place the marker on the left side of the headband, slightly above the ear.
Place the marker on the right side of the head, slight above the ear. For best results, try to place the side markers in an asymmetrical arrangement and avoid creating isosceles triangle from the three markers.
Place the marker on the spine right below the neck. For best results, LUArmHigh-LShoulderBack-BackTop-RshoulderBack-RUArmHigh markers should align roughly in a straight line when the actor is in T-pose. Also, note that this marker must be placed at an elevation higher than the chest marker for the torso segment to be tracked properly.
Place the marker at the center of the sternum, about 5 cm below where the neck starts.
These two markers are located symmetrically on each side of the back, slightly below the lowest end of the shoulder blade (scapular bone).
Note that the waist markers are the key markers in modeling the pelvis bone, which is the major segment governing the other subsequent skeleton segments. For best results, avoid placing the waist markers in a rectangle shape. When tracking multiple actors with similar proportions, introduce an offset to one of the WaistBack marker, or the WaistCMarker (included only with the 13 additional markerset), to create an asymmetrical arrangements.
Placed the marker on the protruding bone located on the front of the pelvis (left/right anterior iliac spine bone). The prominence can be palpated from left and right side of the waist.
Place the WaistLBack and WaistRBack markers above left/right hip; about 10 cm above the hip joint.
When placing the shoulder markers, ask the actor to stand in the
in order to place the markers on accurate locations. It could also be helpful to ask the actor to do few rounds of arm abduction and adduction to palpate for the shoulder axis. These markers determine the width of the shoulder and respective relationship with the upper arm segment.
Place the marker on the shoulder joint (glenohumeral joint) on the back.
Place the marker at the top of each shoulder where you can palpate the protruding bone, which is usually located just before where the upper arm start when in T-pose. More specifically, the prominence is on the distal end of the clavicle bone (acrominoclavicular joint).
Place the marker on the lateral side of the elbow joint, slightly towards the upper arm. More specifically, on the lateral epicondyle of the distal end of the humerous. Ask the actor to flex and extend the arm few times to confirm that markers are placed along the elbow axis and maintain stationary throughout the range of motion cycles.
Place the marker on the back of the upper arm near the groove between the triceps. For best results, LUArmHigh, LShoulderBack, BackTop, RshoulderNack, and RUArmHigh should align roughly in a straight line when in T-pose.
For best results, place the hand markers so that the shape of the marker arrangement is asymmetrical itself and also unique to the shape on the other hand. Since the wrist marker placement is fixed along the wrist axis, offset the HandOut or the HandIn markers to create the unique arrangements. For more robust and simple tracking, hand rigid-bodies can be attached on the hand to replace the markers and guarantee the asymmetrical and non-deforming marker placement.
Fore Arm / Hand
Place the marker on the outside (lateral side) of the wrist axis. (distal end of the radius bone). Note that the wrist axis is not always located on the protruding bone but 1-2 cm more towards the hand.
Fore Arm / Hand
Fore Arm / Hand
Place the marker on the inner prominence (medial side) of the wrist axis (distal end of the ulnar bone).
Fore Arm / Hand
Place the marker slightly below the pinky knuckle. More specifically, between distal end of the fifth and fourth mertacarpal bones.
Place the marker on the front side of the thigh, along the midline. For best results, slightly offset the height of the left and right markers to introduce the asymmetry.
Place the marker on the outter prominence of the knee joint; on the lateral epicondyle of the femur. Palpate the knee for the protruding bone from the upper leg, and place it right on the axis. Ask the actor to flex and extend the knee few times to confirm that the markers are placed along the axis and maintain stationary throughout the range of motion cycles.
Place the marker on the shin bone; on the midline of the lower leg. For best results, slightly offset the height of the left and right markers to introduce the asymmetry.
Place the marker on the protruding bone outside of the ankle joint; on the lateral end of the malleolus bone.
Place the marker just before the little toe joint; on the distal end of the fifth metatarsal bone.
Place the marker just before the big toe joint; on the distal end of the first metatarsal bone.
Hinged Toe Markers
Hinged toe markersets create toe segments in the skeleton. Two additional markers are added to each foot, one on the toe-tip and another on the heel. The hinged toe markers are included in all baseline markersets except for Baseline (37) and Upper Body markersets.
Place at the center of the heel.
Place the marker on the tip of the second toe; next to the big toe.
Retrieved from "
This page was last edited on 21 December 2016, at 00:17.
All data and information contained in or disclosed by this wiki is proprietary information of NaturalPoint Corporation and all rights therein are expressly reserved. By accepting this material the recipient agrees that this material and the information contained therein is held in confidence and in trust and will not be used, copied, reproduced in whole or in part, nor its contents revealed in any manner to others without the express written permission of NaturalPoint Corporation. Information in this document is preliminary and subject to change and does not represent a commitment on the part of NaturalPoint Corporation.
2019 NaturalPoint, Inc. DBA OptiTrack